Why Road Trek Macerator Pump Not Working

Because they are lightweight and easy to move, recreational vehicles, also known as RVs, are one of the best types of automobiles to use for camping adventures. Several conveniences are incorporated inside them, including a bathroom, a bedroom, and a kitchen, which allows you to prepare your own food. You may enjoy a relaxed vacation while yet feeling as if you are traveling in your own backyard if you use these methods.

It is crucial to note, however, that keeping your automobiles in good functioning order is just as critical. Maintaining the plumbing system of an RV is equally as vital as maintaining the engine, tires, and other components. Companies have created tools to make dealing with this procedure more convenient, but it may be incredibly frustrating at times, so be prepared.

Most of the time, it is very simple to operate and set up a device such as the Road trek Pump, which is an example of this. Only a small number of customers, however, have expressed dissatisfaction with the way the Road trek Macerator Pump is working. I’ll walk you through several troubleshooting approaches in this article to assist you in addressing the issue.

How to know if a macerator is working

Roadtrek macerator pump not working

When you look through clear elbows, you can see how well the macerator pump is performing, which is beneficial. System indicators such as back flushing and obstruction should be detectable by the device.

Try to keep your ears as close to the macerator pump as possible if you aren’t planning on staying and witnessing the procedure. In the event that you hear a high-pitched whine, it is probable that you have a blockage. This indicates that the macerator is low on water.

It’s possible to blow fuses when using macerators because they consume a significant amount of electricity. Extreme caution should be exercised while determining the amount of power provided by an RV battery or battery pack prior to purchasing a macerator pump.

The macerator contributes to the reduction of the demand for landfills by slicing up and dropping recycled papers directly into the waste system. A further method for reducing environmental effect is to reduce water and electricity use as a result of the short cycle durations.

How an RV macerator pump works

The use of a macerator pump while disposing of garbage from your RV could help you to reduce the amount of mess. It reduces the size of the waste to a slurry by grinding and crushing the larger pieces.

This can be really beneficial for moving rubbish up an incline. – Just to put it another way, having a macerator pump gives you more options when it comes to locating waste disposal sites. In your recreational vehicle, the method used, as well as its advantages and disadvantages, varies slightly depending on the type of macerator pump that you have installed.

A macerator pump on a recreational vehicle can be found in two different configurations: as a separate device or as a permanent built-in macerator (RVs). In addition, it is crucial to understand that not all macerators are powered by electrical current. Hydraulic valves are a fantastic choice for individuals who already have a reliable backflow assembly to use in conjunction with their valves.

This equipment is put in your basement and functions effectively as a garbage disposal system for your black water tank. This process grinds up the waste, resulting in a waste product that is thinner and more fluid in consistency. Consequently, you will be able to pump waste over longer distances and at a steeper grade without experiencing any difficulties.

a) Connect the pump to the sewage drainage point, if one does not yet exist.

b) Connect the sewage pump to the sewage drainage point.

c) The discharge line of the pump should be connected at this point as well.

d) The free disposal point should be linked to the opposite end of the hose. 

e) The pump should be connected to an open outlet or, if at all feasible, directly to the battery. 

f) The valve should be opened in order to drain the water. 

g) To begin using the pump, hit the start button on the control panel.

h)  After the waste flow has been completely stopped, turn off the pump and store it safely.

i)  Reposition the toilet for a few seconds so that it is back in its original location.

j) The pump should be brought back into normal operational condition. 

k) Then repeat the previous two processes until only clear water can be seen flowing out of the spouting. 

The pump, unlike many other electric pumps for liquids, can be damaged if it is left running dry. It should be noted that this is a widespread problem that affects even certain high-end makers. Always turn off the pump once the flow has been stopped to avoid any harm to the motor.

Purchasing a clear elbow is necessary in order to connect the RV sewer hose to the waste valve fitting. Even though they aren’t always required, having these on hand is a wise precaution to take. It will be useful to be able to visualize the working of the macerator pump by using clear elbows. The following procedure should be used in order to detect back flushing or clogging.

How does a macerator toilet work in an RV?

How does a macerator toilet work in an RV

A standard American toilet draws waste and wastewater down into the washroom and out of the washroom by gravity, which is placed below the level of the waste being flushed. Essentially, it is an up flush toilet system that directs waste to an in-wall or even behind-the-door receptacle after waste has been flushed.

When waste enters the container, it is liquefied by a high-powered macerator knife, which is then pumped out of the device through a pipe that links to the main sewer line of your residence. Even while these toilets are often more expensive than a traditional American toilet, they are significantly less expensive than the cost of designing and installing a completely new pipe system in order to install a toilet in your home.

 It is not suggested to utilize macerator toilets as the primary toilet system for a large household or family of any size. This is owing to the fact that if the pump is used every day, all day long, by a large number of people, it will ultimately become overworked and fail.

How long does a macerator pump last?

With macerator pumps, the general rule is that a machine that handles a small quantity of trash will typically survive up to 15 years if it is properly maintained. With ordinary usage in a master bath in a residential home, you may expect a macerator to last for at least 10 years under normal circumstances.

The usual guideline for macerators is that the machine serves as an additional 2nd toilet and is only built to withstand a limited amount of traffic, meaning that it should last for at least 15 years, depending on how it is used and maintained. A macerator should last approximately 10 years in an average-sized home when used as the primary bathroom.

The Saniplus is a 1/2 HP pumping system that can be used to install an entire bathroom down to 15 feet below the sewage line, or even down to 150 steps away from a soil stack, depending on the application. Within the unit there is a macerating mechanism that is capable of handling human waste and toilet roll in residential applications.

Reasons a road trek pump may not pump

Reasons a road trek pump may not pump

1. A failed motor

Additionally, the motor on your Road trek Macerator Pump could have failed, which would explain why you are experiencing this problem. This can occur as a result of electrical defects in certain instances, while in others, the motor can simply fail as a result of wear and tear over time.

In order to determine whether or not our motor was the source of the problem, you can troubleshoot the item and then replace it. Remove the old motor and get in touch with the company to make arrangements for a new motor to be installed.

 According to your location, you may be able to find merchants who will sell you the motor; however, you must first make sure that the motor is compatible with your car before making a purchase. It follows that you will be less prone to experience difficulties in the future.

2. Solidified black tank

If the black tank in the vehicle’s toilet becomes clogged, it is likely that the pump will stop working. If you have not cleaned out your tank in a lengthy period of time, you will have this problem. It is as a result necessary to regularly empty and clean your tank in order to maintain its correct condition.

As a result, it is hoped that your pump will not experience any such issues in the future. For those who already have a problem with their pump, you will need to remove the complete pump and all of the piping leading to it.

Conclusion

Whether or not to utilize a macerator pump is a matter of personal preference. Not everyone is enthusiastic about the prospect of taking on another piece of equipment that requires constant maintenance. Using a macerator pump can be quite dangerous, and some people may not be aware of the dangers involved.

Alternatively, you can put a macerator pump in the toilet, which will turn everything into a sludge when you flush it.

About Me

This is Cody Wingfield; I’m an author and a Freaky Campers enthusiast. My three favorite activities are Cycling, Rving, and Cooking for me. OutingX is a planet of mine where I will share my exploring history, story, freaky experiment, and personally gathered experience with you.

Leave a Comment